Search The ForumSearch   RegisterRegister  LoginLogin

MailBee Message Queue
 AfterLogic Forum : MailBee Message Queue
Subject Topic: Timeout Settings Post ReplyPost New Topic
Author
Message << Prev Topic | Next Topic >>
Michael Fox
Guest Group
Guest Group


Joined: 10 November 2003
Online Status: Online
Posts: 262
Posted: 17 December 2005 at 11:34am | IP Logged Quote Michael Fox
No matter what timeout setting I use, it always uses 30 seconds. How do I actually change it, I need to set it to 10 seconds.

Thank You
Michael Fox
webmaster@m3lgs.com
M3 Lead generation Systems
http://www.m3lgs.com
Back to Top View Michael Fox's Profile Search for other posts by Michael Fox
 
Alex
AfterLogic Support
AfterLogic Support
Avatar

Joined: 19 November 2003
Online Status: Offline
Posts: 2206
Posted: 17 December 2005 at 5:13pm | IP Logged Quote Alex
Perhaps, the changes you applied to the ini file just didn't take effect. To apply the changes, stop/uninstall the service (Stop and Uninstall the service.bat) and then install/start service back (Install & Start the service.bat).

If, however, you're pretty sure timeout is still not changed, could you please provide more information about the situation when the timeout occurs along with the log file? Thanks!

Regards,
Alex
Back to Top View Alex's Profile Search for other posts by Alex
 
Michael Fox
Guest Group
Guest Group


Joined: 10 November 2003
Online Status: Online
Posts: 262
Posted: 21 December 2005 at 1:10pm | IP Logged Quote Michael Fox
It did save the settings. The ini file is below. The situation is, the queue tries to send a message and while it should only wait 10 seconds, it is waiting 30 seconds. An exerpt from the log file is below as well.

--------------------------------------
[Main]
LicenseKey="***********"
QueueDirPath="D:\MessageQueue"
[Logging]
EnableLogging=yes
LoggingLevel=2
LogFilePath="D:\MessageQueue\log.txt"
[Timings]
PollingInterval=2
SendsPerSecond=4
SendsPerSession=20
Timeout=10
[SMTP]
ServerName="***********"
DomainName=null
PortNumber=2500
UserName="***********"
Password="***********"
AuthMethod=1
[Problems]
KillUnsentMessages=no
--------------------------------------

--------------------------------------
11:20:18 Sending message from file 00007851.mbm
11:20:18 Reading message file
11:20:18 Sending MAIL FROM command
11:20:18 Sending RCPT TO command
11:20:18 Dot at line start found, performing parsing
11:20:18 Dotting the message end
11:20:18 Sending DATA command
11:20:18 Sending sequence of data chunks
11:20:18 Sending full-size (8192 bytes) data chunk
11:20:18 Sending partial data chunk
11:20:18 All data chunks have been sent
11:20:18 The message has been successfully sent
11:20:18 Sending message from file 00007852.mbm
11:20:18 Reading message file
11:20:18 Sending MAIL FROM command
11:20:18 Sending RCPT TO command
11:20:18 Dot at line start found, performing parsing
11:20:18 Dotting the message end
11:20:18 Sending DATA command
11:20:18 Sending sequence of data chunks
11:20:18 Sending partial data chunk
11:20:18 All data chunks have been sent
11:20:38 ERROR - No response: connection is lost
11:20:38 ERROR - The message has not been sent due connection failure
11:20:40 Searching for the messages... Folder is D:\MessageQueue\*.mbm
11:20:40 Connecting to server...
11:20:40 Connected to server
11:20:40 Sending message from file 00007852.mbm
11:20:40 Reading message file
11:20:40 Sending MAIL FROM command
11:20:40 Sending RCPT TO command
11:20:40 Dot at line start found, performing parsing
11:20:40 Dotting the message end
11:20:40 Sending DATA command
11:20:40 Sending sequence of data chunks
11:20:40 Sending partial data chunk
11:20:40 All data chunks have been sent
11:21:10 ERROR - No response: connection is lost
11:21:10 ERROR - The message has not been sent due connection failure
11:21:12 Searching for the messages... Folder is D:\MessageQueue\*.mbm
---------------------------------------
Back to Top View Michael Fox's Profile Search for other posts by Michael Fox
 
Alex
AfterLogic Support
AfterLogic Support
Avatar

Joined: 19 November 2003
Online Status: Offline
Posts: 2206
Posted: 22 December 2005 at 3:54pm | IP Logged Quote Alex
Please try to install the newer version of MailBee Message Queue at http://www.afterlogic.com/updates/mmqsetup.exe and let us know if this helps.

Regards,
Alex
Back to Top View Alex's Profile Search for other posts by Alex
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

Forum Jump

Powered by Web Wiz Forums version 7.9
Copyright ©2001-2004 Web Wiz Guide